Elastomeric Roof Coating & Waterproofing Protection
If you believe you'll be conserving the roof decking plywood (not changing it), then you might conserve yourself some cleanup problem by getting rid of the fixtures first and then peeling up the rubber! Information of water damage on camper roofing. More water damaged areas on RV roofing system decking. There was nothing actually horrible that made me feel like I was going to fail, but definitely a great deal of damage and I was getting the feeling I would be replacing a lot of the roofing system decking plywood.
Which Roof Coating Performs Best?
Hop Over To These Guys: best rated roofers in Tucson AZ - DC Roofing of Arizona http://angelorusy364.yousher.com/spraying-elastomerics-and-roof-coatings-a-complete-guide
I chose the simplest one initially, a vent cap from a kitchen sink plumbing vent pipeline. Starting to scrape caulk and sealant. I utilized a stiff scraper with a chisel-like blade and simply began spying and chipping and scraping and hacking. There is no other method around this, you simply have to begin digging until you expose the screw heads.
Loosening the screws in vent cap. The screws on this vent cap were hex-head metal screws so I utilized a small socket motorist to eliminate them. Some came out tidy. Others were rusted and I needed to utilize a vice-grip pliers to get the heads and turn them gradually.
I discovered an old wasp nest inside the vent cover. This is a sight I'll probably need to get used to, finding the remains of animal habitation in every nook and cranny. I spend a terrible great deal of my time producing excellent wildlife environment in my lawn so I do not get offended when an animal selects to set up house in my Recreational Vehicle.
Roof Coatings, Roof Paints And Waterproof Roof Coatings
Luckily nobody was house in this old nest so I simply tossed it. Maybe I'll put a screen over it when changing it. Which brings us to the next point. You should try not to harm these pieces (like vent covers and caps) as you're removing the old caulk and sealant simply in case you require to utilize them once again.
(Think I'll discover out when the roof is done!) Prying up the vent cap and eliminating the last ring of rubber roofing underneath. So I pried up the rest of the cap and scraped up the staying rubber roof and butyl tape and putty and 25 years of other gunk and here's how it looks tidied up.
White-seal 100% Acrylic Elastomeric Reflective Roof
One down, 7 more fixtures to go. Next I decided to take on the only roofing ventilation fan that my camper has. My roofing vent likewise had a vent cover over it. So I began scraping the gunk from those screws. Starting on the roofing system vent. Hardware exposed on roofing vent cap, the first nut came off tidy.
How Much Does Roof Coating Cost Per Square Foot
Bolt is spinning. The fasteners on this RV roofing system vent cover were nuts on little bolts. The first one came off great with an extension socket kit. The second one just began spinning, suggesting the bolt was not fixed in place however turning in addition to the nut. Downer. A peek at the hardware holding down the roofing vent cover.
Elastomeric Roof - Premium Acrylic Coatings
I didn't have any excellent way to hold the bolt in location so instead I decided to saw through the bolts with a reciprocating saw. Sawing through bolts on roof vent cover. I utilized a cordless reciprocating saw with a metal-cutting blade however it was tricky to get the blade flat adequate to reach the bolts so close to the roofing deck. The majority of were so old and rusted that they sheared off when I unscrewed then with a great deal of force. Unscrewing the brackets that held the vent cover in location. Then I scraped more caulk and roofing sealant off the flange of the roofing vent itself. I quickly found there disappeared screws or hardware holding it down so I provided up on the scraping and went inside the RV After scraping the caulk and sealant from flange of roof vent, say goodbye to screws! Unscrewing the inside cover plate of roof vent fan in RV bathroom.
A couple sheared off with a great deal of force, however two would not budge. So I had to drill out the screw heads. I chose a drill bit near the size of the shaft of the screws that I had currently taken out and started drilling. Selecting a drill bit for drilling out a screw head.
Shatterproof glass recommended. So I drilled out the heads, one popped off and the other I was getting annoyed with and provided it a pull before it was drilled through. Rather of popping off the screw head, the plastic simply disappeared around the hot screw head. Whoops. Hope I don't have to reuse this cover.
If not, I'll need wider screw heads when re-assembling. Cover plate gotten rid of from roof vent. Next I discovered little corner brackets with hex-head bolts holding them in. I unscrewed them (all came out great luckily) and took out the brackets and little white plastic spacers. Loosening corner brackets in roofing vent.
A Coatings Specialist Explains How To Correctly Apply Roof Coating
All corner brackets got rid of, all set to pull out. When the brackets were out I went back up leading to pry out the the roof vent. Then I scraped up all the staying gunk and rubber roof. Taking off the old roof vent. There are two wires running to the roofing system vent (a black hot wire and a white neutral wire) that you'll require to clip to get rid of the old vent.